VIRTUFIT ICONSOLE HTR 2.1 FREE
At the time of writing, I'm not sure if I think it's worth paying for the app (I'm still in my 7-day free trial). Kinomaps does offer a bit more, however, but for the price of 9.99 per month (or 79.00 per year). I had pre-installed the iConsole and Kinomaps apps on my iPad, and created accounts for them, so I could get started right away. In other words, the quality is not the same across the board. The body with the handlebar and saddle rod are solid, but the various plastic parts feel very rickety here and there. The different parts just don't always feel equally solid.
VIRTUFIT ICONSOLE HTR 2.1 MANUAL
I don't agree with the various complaints that the assembly and manual are difficult or unclear. Top device!Īfter delivery, I put the thing together on my own in less than half an hour. After 2 workouts on this bike I am completely sold. I chose this model based on many reviews on various sites. In the past, I've cycled a lot in different gyms, and I was specifically looking for one that felt as sturdy and solid as one in the gym. I am a hobby cyclist who, now that autumn is approaching, still wants to maintain a bit of condition, and therefore was looking for a solid home trainer. Not every part is of the same solid quality 17 18.Endless possibilities through various apps 18) onto the seat post by sliding the post into the seat slider while pulling on the pull pin under the seat slider. Locate the seat slider and mount the assembly (Fig. Hardware QTY M8x1.25x12mm hex Screw 2 Final Torque 33-37 Lb-Ft (45-50 Nm) Fig. 17) thru the back of each crank arm and torque each screw to its final value. Insert the pedal securing bolts into each pedal (Fig.
VIRTUFIT ICONSOLE HTR 2.1 INSTALL
21) and install the corresponding hardware to lock the plastic sleeve in place.Īssembly Manual 16. Mate the edge of the plastic sleeve flush with the edge of the upright tube (Fig. 20) into the frame by pulling on the pull pin located on the upright column of the frame and sliding the post downward along with the plastic sleeve verifying to lock the post into one of the available positions. Remove all parts from the shipping carton and foam insertĪssembly Manual Hardware QTY M4 x 10mm Phillips Pan Head Thread Form S crew 2 19. Carefully tilt the box forward so that the box may be lifted to expose the bike. Open the top of the carton and fold back all four flaps. UNPACKING AND PARTS LIST Position the shipping carton so the “Heavy End” logo is located at the bottom. 12) toĪssembly Manual StairMaster AirFit Assembly & Setup Use the following procedures to unpack and assemble your AirFit manufactured by StairMaster. Secure the left & right grip arms to the crank linkages by applying final toque (Fig. Hardware QTY M24 x 1.5 Hex Jam Nut 2 Final Torque 48-50 Lb-Ft (65-67.8 Nm) Fig. 11) by threading the large jam nut onto each pivot shaft and applying the corresponding final torque to each nut. Stairmaster AirFit Assembly Manual Hardware QTY M8 x 20mm Button Head Bolt 4 10. 15) stamped into the strap that indicates the user side for i ASSEMBLY TIP Each pedal has an “L” or “R” marking (Fig. 14) over the mounting plates and secure the covers from the underside by bolting four button head cap screws along with washers into the corresponding four available holes. Attach the left & right plastic foot stand covers (Fig. 10) onto the corresponding pivot shafts located onĪssembly Manual Hardware QTY M8 x 15mm Button Head Bolt M 8 x 16mm O.D. 9) to the frame using the four pre- installed Phillips head screws thru each of the available holes on the neck plate. 8) over the neck mast and connect the cable coming out of the mast into the cable protruding from the console. Test the seats horizontal adjĪssembly Manual Hardware QTY M8 x 20mm Socket Head Cap Screw M 8 x 25mm O.D. Check the seat to make sure it is level and tight and does not rotate around or tilt. Test the seat post to make sure they move freely and you are able to lock in at different positions. Recheck all the bolts and make sure they are all tightened to the proper torque specification (when indicated) and no parts are missing. 3Īssembly Manual Testing Bike Use this checklist to perform the bike test procedure. 2) of the c ardboard box to expose the base and assembly components of the m achine. Cut all straps and remove the top half (Fig. Locate an open area to unbox the packaged machine (Fig.